$39 Diagnostic, Credited to Your Repair

Furnace Repair in Park City, UT

Snow over the vents, a furnace running nonstop at about 7,000 feet, or a second home that went cold while you were gone? We find the real problem and put the price in writing before we start. $39 to diagnose it.

  • Licensed & Insured
    Lic #14278324-5501
  • 5-Star Rated
    on Google
  • $39 Diagnostic
    Goes Toward the Repair
  • 24/7
    Emergency Service

Furnaces Work Harder in Park City

Park City sits at about 7,000 feet. Winters are longer and colder than down in the valley, and the snow piles up deep. A furnace up here might run twice as many hours as the same furnace in Sandy, so parts wear out sooner and small problems turn into no heat faster.

A lot of Park City homes are second homes or rentals, and that changes things. When a furnace quits and nobody is there, it can turn into frozen pipes and a much bigger bill. We'll work with you, your property manager, or your rental company to get in and get the heat back on.

We're based in Sandy, about 40 minutes from Park City over Parleys Canyon. We come up for furnace calls in Old Town, Park Meadows, Kimball Junction, Jeremy Ranch, and everywhere in between.

What We Fix on Mountain Furnaces

These are the furnace calls we run up here most. Snow, cold, and elevation cause problems you don't see as much in the valley.

Vent pipes buried in snow

High-efficiency furnaces breathe through two PVC pipes on the side of the house. When snow drifts or slides off the roof and covers them, the furnace shuts itself down to stay safe. Up here that happens every winter.

Frozen condensate lines

These furnaces make water. If the drain line runs through a cold garage, crawlspace, or outside wall, it can freeze on a cold night and the furnace locks out until the water can get out.

Furnaces that never get a break

At about 7,000 feet, a furnace runs a lot more hours than one in the valley. Igniters, inducer motors, and blower motors wear out sooner, and a dirty filter does more damage.

Elevation setup

Gas furnaces up here have to be set up for the altitude, per the manufacturer's high altitude instructions. When that step got skipped, we see rough flames, soot, and pressure switch lockouts.

Second homes nobody was watching

A furnace that quits while the house sits empty can mean frozen pipes by the time anyone finds out. We work with owners and property managers to get in, find it, and get the heat back on.

Flame sensors and igniters

Still the most common no-heat calls, anywhere. Quick fixes, and we keep the common parts on the van so we're not driving back down the canyon for one.

Before You Call, Check These

A few of these solve the problem without a service call, and that matters when we're driving up the canyon.

  • Thermostat is set to Heat and a few degrees above the room
  • The two PVC vent pipes outside aren't buried in snow or ice. Clear them by hand, gently.
  • The filter isn't packed with dust
  • Furnace switch and breaker are both on
  • No water around the furnace or a frozen drain line
  • Smell gas? Get everyone out, don't touch any switches, and call Enbridge Gas or 911 from outside
Furnace diagnostic
$39

That's our weekday fee, Monday through Friday, 9am to 5pm, to come out and track down the problem. If we do the repair, the $39 is credited toward it.

Nights, weekends, and holidays: $99.

Schedule a Repair

What Furnace Repair Costs in Park City

These are the repairs we do most in Park City and what they usually run. You get the exact number in writing before any work.

RepairTypical price
Flame sensor clean or replaceLights, runs for a minute, then shuts down. This is usually why.$105 to $445
Blower wheel cleaning or replacementYears of skipped filters pack the wheel with dust.$275 to $475
Inducer motor replacementA common big repair on furnaces put in during the 90s.$950 to $1,250
Blower motor replacementWhen the main fan motor finally wears out.$450 to $1,900

Duct repairs and sealing old swamp cooler vents are quoted on site. See our full furnace repair price list for other parts.

Real Furnace Work

Photos from our own furnace calls, not stock pictures.

Furnace secondary heat exchanger before and after cleaning
A secondary heat exchanger before and after cleaning. Skipped filters lead to buildup like this.
Multimeter testing a furnace part
Testing a part with a meter before we replace it. You only pay for what's actually bad.

What Homeowners Say

"Michael is knowledgeable, dependable, thorough, and really cares about helping his customers. He goes above and beyond, taking the time to explain things clearly and making sure everything is handled properly."
Sheila B.HVAC service
"Great team and very responsive, was able to get help with our AC quickly and they were informative without being pushy or overbearing!"
Taylor C.HVAC service
"They did a thorough inspection and cleaned both the indoor coil and outdoor condenser. The technician explained what they were doing, was professional, and left everything clean when they were finished."
Tech M.HVAC tune-up

Park City Furnace Repair FAQs

How much does furnace repair cost in Park City?

A weekday diagnostic is $39, and it goes toward the repair if you go ahead. Small parts like a flame sensor or igniter usually run $105 to $450. Bigger parts like an inducer motor or control board run $350 to $1,900, depending on the furnace. You get the price in writing before we start.

My furnace quit during a snowstorm. What happened?

Check the two white PVC pipes on the outside of the house first. If snow or ice covered them, the furnace shuts down on purpose. Clear them gently, turn the furnace off for a minute, and turn it back on. If it still won't run, give us a call.

I'm not in town. Can you get in and fix it?

Yes. Give us a door code, a lockbox, or your property manager's number and we'll set it up. We send you what we found and the price, and nothing gets repaired until you say so.

Does elevation really matter for a furnace?

It does. Gas furnaces are built for sea level, and the manufacturer has instructions for setting them up at higher elevations. If that wasn't done, the furnace can burn rough, soot up, or lock out. We check it on every call up here.

Do you come up to Park City on nights and weekends?

Yes. Nights, weekends, and holidays are a $99 dispatch fee. Weekdays 9 to 5 it's $39, and that goes toward the repair.

Where We Work Around Park City

All over Park City and the Snyderville Basin, from Old Town, Park Meadows, Prospector and Deer Valley to Kimball Junction, Jeremy Ranch, Pinebrook and Silver Springs.

Old TownPark MeadowsProspectorDeer ValleyKimball JunctionJeremy RanchPinebrookSilver Springs

No Heat in Park City? Give Us a Call

Book online or call. We'll find the problem and tell you the price before we fix anything.

Scroll to Top