Furnace Replacement in Draper, UT
Builder furnace finally giving out? We're right next door in Sandy. We size it to your Draper home, give you options in writing, and install it to code.
- Licensed & Insured
Lic #14278324-5501 - 5-Star Rated
on Google - Free In-Home
Estimate - Financing
Available
What We See in Draper Homes
Most Draper homes were built from the 1990s on, and a lot of them still have the furnace the builder put in. Those are hitting 20 to 30 years old now, and many were sized by rule of thumb, not by the house.
Bigger two-story homes in Draper often have two systems, or one furnace trying to heat both floors. That's where you see a hot upstairs and a cold basement. Sometimes the right answer is a two-stage furnace with zoning instead of just a bigger unit.
Up on the hill in SunCrest and Corner Canyon, winters run colder and windier than the valley floor, and the altitude matters for furnace setup. We account for both when we size and set up the furnace.
Is Your Draper Furnace Ready to Go?
These are the signs we see most on furnaces around 20 years old.
Original builder furnace
If the sticker inside says the 90s or early 2000s, it's near the end, and parts are getting pricey.
One floor hot, one floor cold
Common in two-story homes. A properly sized two-stage furnace or zoning can even it out.
Loud start up or rattles
Worn inducer or blower bearings. On an older unit these are big tickets.
Repairs every winter
When you're calling every season, that money is better spent on something new.
Heat exchanger concerns
A crack or failed CO test means replacement. We show you what we find.
Higher gas bills each year
An aging 80% furnace loses efficiency every year it runs.
What a New Furnace Costs in Draper
Installed price ranges for Draper homes. Larger homes and two-system houses are priced per furnace.
| Furnace | Installed price |
|---|---|
| Standard 80% furnaceSimplest swap when the existing venting stays. | $4,000 to $6,500 |
| High-efficiency 96% furnaceLower gas bills and quieter. Rebate eligible. | $6,500 to $10,500 |
| 97% modulating furnaceBest for big, two-story homes that struggle to stay even. | $8,500 to $12,500 |
| Second system or zoningFor homes with two furnaces or one that can't heat both floors. | Quoted on site |
Ranges are typical. Your price depends on size, efficiency, venting, and whether we're matching an existing AC coil. Everything is in writing before we start.
What's in the Price
- Sizing based on your home
- Matched to your AC coil and ducts
- Gas connection and shutoff
- Venting for the furnace type
- Condensate drain on high-efficiency
- Draper permit and inspection
- Old furnace removed
- Safety and CO testing
- 2 year labor warranty from us on a new furnace, 5 years when we replace the whole system, plus the manufacturer warranty registered for you
Enbridge Gas pays $300 on a 95% to 97.4% furnace and $350 on 97.5% and up, in an existing home. Our 96% and 97% furnaces qualify, and we help with the paperwork. Rebates are set by ThermWise and can change.
Want to spread it out? Check financing in about a minute with no hit to your credit.
Check FinancingFix It or Replace It?
A lot of Draper furnaces are right on the line. Here's the honest version.
Fixing it is usually the move when
- Under 10 years old with parts warranty left
- A small part failed
- No heat exchanger issues
Replacing it makes more sense when
- Original builder furnace near 20 years or more
- Big part needed on an older unit
- Uneven heat that a repair won't fix
We'll price both on the same visit. Just need it running? See furnace repair in Draper.
Real Photos From Our Jobs
Venting and equipment from jobs we have done, not stock photos.
How a Replacement Goes
Book a free estimate
Book online or call. We come out, look at the house, and measure what it actually needs.
Get options in writing
Usually two or three furnaces at different price points, with the full installed price on each.
Install day
Most swaps take one day. Old furnace out, new one in, gas, venting, and drain hooked up to code.
Test and walk through
We test combustion and carbon monoxide, set the thermostat, and show you the filter and basics before we leave.
What Homeowners Say
"Michael is knowledgeable, dependable, thorough, and really cares about helping his customers. He goes above and beyond, taking the time to explain things clearly and making sure everything is handled properly."Sheila B.HVAC service
"Great team and very responsive, was able to get help with our AC quickly and they were informative without being pushy or overbearing!"Taylor C.HVAC service
"They did a thorough inspection and cleaned both the indoor coil and outdoor condenser. The technician explained what they were doing, was professional, and left everything clean when they were finished."Tech M.HVAC tune-up
Draper Furnace Replacement FAQs
How much does a furnace cost in Draper?
An 80% furnace typically runs $4,000 to $6,500 installed, a 96% runs $6,500 to $10,500, and a 97% modulating runs $8,500 to $12,500. The estimate is free.
Do furnaces need to be set up differently in SunCrest?
Yes, some. Higher elevation changes how the furnace burns gas, and the manufacturer has altitude settings for it. We set it up for where your house sits.
Should I replace my AC at the same time?
If the AC is about as old as the furnace, often yes. One install, matched equipment, and you're set for years. See AC replacement.
Is a two-stage furnace worth it?
In a bigger Draper home, usually. It runs on low most of the time, which means quieter, longer, more even heat.
Can I use a heat pump in Draper?
Yes. Rebates from Rocky Mountain Power and Enbridge can reach $2,650. See heat pumps.
How soon can you install?
It depends on the equipment. Common furnace sizes are usually easy to get, so it often moves quickly. You get an install date when you approve the job.
Draper Neighborhoods We Cover
We're based in Sandy, so Draper is a short drive. South Mountain, SunCrest, Corner Canyon, and everywhere in between.
Get a Furnace Price for Your Draper Home
Free estimate, real options, and the price in writing.